Howard County: divided by density?
Some parts of the county have a hundred times more people per square mile
A long-time theme in writings about Howard County is the distinction between the more densely populated suburban and semi-urban areas like Columbia and Ellicott City and the less densely populated rural areas in the western part of the county. This has implications for issues from political affiliations to school redistricting, and of course for affordable housing as well.
In this post I’m going to ignore those issues though, and just look at the simple facts about density variation across the county. The map above shows density variations as of the 2010 census—a data source I chose because it contains accurate population counts at a fairly fine-grained level. The map shows population densities (people per square mile) for each of the 154 census block groups within the county.
A census block group is a geography defined by the U.S. Census Bureau that is one level below a census tract. There are currently 154 census block groups in Howard County, compared to 55 census tracts. The smallest geography in U.S. Census data is the census block, one level below the census block group. There are currently 4,845 census blocks defined for Howard County.
Census tracts are relatively large, about 6,000 people or so on average in Howard County. On the other hand, census blocks are too small: more than half of all census blocks in Howard County contained no people at all.
Census block groups are a nice “not too large, not too small” subdivision of the county’s overall area. In 2010 the least populated census block group contained 645 people, while the most populated census block group contained 3,632 people. The smallest block group covered an area of 0.1 square miles (about 64 acres), while the largest block group covered an area of 13.4 square miles.
A typical census block group is thus comparable in both size and population to a traditional village or small town. It is large enough to be a recognizable “place”, but small enough to have its own identity distinct from that of other places in the county.
What about density? One of the most surprising things to me in doing this analysis was the wide variation in population density across the county. Population density in 2010 varied from a low of 151 people per square mile to a high of 15,181 people per square mile, a difference of two orders of magnitude. In comparison, overall population density for the county in 2010 was 1,144 people per square mile.
As shown in the above histogram, and also in the map above, there are many census block groups in Howard County that had a population density of less than 500 people per square mile in 2010. At the other end of the spectrum a few census block groups had population densities of well over 10,000 people per square mile.
To help think about what these numbers mean, consider a square mile, about 640 acres. Suppose we have a few neighborhoods of houses on 3- to 4-acre lots, with 3-4 people per house. With 50-100 total houses we have a total of 150-400 acres and 150-400 people. Throw in two or three 100-150 acre farms plus road surfaces and open spaces and you’d have a typical Howard County rural census block group with a population density of 200-500 people per square mile.
Now suppose instead we have 0.1 square miles, about 64 acres, occupied by five or six apartment buildings with 50-100 units each, with two to three people per unit. Now we have 500-1,800 people total on that 0.1 square mile area, for a total of 5,000 to 18,000 people per square mile, a typical semi-urban setting in Columbia or eastern Howard County.
How is population density in the various parts of Howard County changing over time? It’s hard to get a good picture of this in between censuses, because the available estimates are from surveys taken over multiple years (from 2013 through 2017 for the latest available data) and have fairly high margins of error (up to 30% or more above or below the estimates themselves).
The map above is an attempt to show density changes from the 2010 census forward, using the American Community Survey 2017 5-year estimates. As with population density itself, there is wide variation in population density changes.
A few areas stand out as having significant increases in population density, from 50-100% more. These appear to be include the Maple Lawn Farms development in Fulton as well as adjacent neighborhoods south of MD 216, areas along U.S. 1 south and north of MD 175, and areas near downtown Ellicott City.
Other areas actually experienced decreases in population density. Assuming that the number of housing units did not decrease in those areas, this likely was caused by the number of people per household decreasing, for example due to children leaving families and “empty nesters” remaining. (Additional census data, for example on household size and the ages of household members, should be able to confirm or refute this idea.)
To sum up: we may argue about how the density divide in Howard County came about and what it all means, but I don’t think there’s any dispute that it exists. It is especially clear in western Columbia, where the drop off in density west and north of MD 108 and (to a lesser extent) south of MD 32 is particularly dramatic. It’s also apparent that new development and demographic changes in family size are having disparate impacts across the county.
Combining this density data with information on socioeconomic and political variables could uncover some interesting patterns. Hopefully I’ll have time in future to look at this. In the meantime, for the code and data used to produce the graphs above, as well as some additional graphs, see “Howard County density trends by census block groups”.
That’s all for this week. A reminder: if you find these posts interesting and useful please tell other people about them and encourage them to subscribe to the Civility and Truth mailing list. Having readers who care enough to subscribe helps motivate me to send these posts out on a regular basis, and the more readers I have the more motivated I’ll be. In the meantime, thanks for reading this post!